To activate, go to www. However, heat caused by hot climates or frequent high loading conditions may accelerate the aging process and may require new tires to be installed more frequently. If the source of the symptom has been identified as a result of this test, proceed to the appropriate section for further diagnosis and repair. If the source has not been identified, continue with the road test. Failure to follow this instruction may result in serious personal injury. Item Description 1 Measure the amperage using a digital multimeter 2 Measure the voltage using a digital multimeter 3 Measure the resistance using a digital multimeter 4 Measure the length or distance 5 Check that the specified pressure is available using a suitable pressure gauge 6 Measure the pressure at the specified port using a suitable pressure gauge 7 Measure the time with a stopwatch 8 Wait for the indicating amount of time 9 The minimum temperature for the specified task 10 The maximum temperature for the specified task 11 The allowable temperature range for the specified task 12 The required temperature for the task 13 Measure for the specified movement 14 Measure for movement not to exceed specified amount 15 Measure for the miniumum-specified movement General Equipment Symbols The general equipment symbols specify which general equipment is used to carry out the procedure. The fuel system may be under pressure.
Did the mirror adjust to the high reflectance clear mode? Cracks A mid-frequency sound, related to squeak. Remove the roof mounted spoiler. Failure to follow this instruction may result in serious injury to vehicle occupant s. Gently pull the parcel shelf upper trim panel toward the center of the vehicle to release the 4 parcel shelf upper trim panel retaining clips and position the parcel shelf upper trim panel aside. For a list of these tools, an explanation of their uses and a glossary of common terms, refer to Section 100-04. Failure to do so may result in incorrect restraint system operation, which increases the risk of personal injury or death in a crash. Remove the rear hatch scuff plate trim panel.
To install, reverse the removal procedure. Separate sections of the Ford Fiesta manual include operating instructions, electrical equipment wiring diagrams for a car, and maintenance recommendations. Hertz Hz A unit of measure used to describe noise and vibration concerns expressed in cycles per second. With the help of an assistant, disconnect both liftgate shocks at the liftgate. Chatter A pronounced series of rapidly repeating rattling or clicking sounds.
The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the Tire Label, which is located on the B-pillar or edge of the driver's door. Also referred to as a shimmy or wobble. Male to female pin terminal fit is critical for connection reliability. These systems may become damaged in a crash. Ut fringilla vel elit ac maximus.
The battery is heavy and could fall. For additional information, refer to the procedures in this section. Working from the bottom of the front door trim panel, Disengage the 8 pushpins from the door. Pinpoint Tests Pinpoint Test E: The Auto-Dimming Mirror Does Not Operate Correctly Refer to Wiring Diagrams Cell 124 , Power Mirrors for schematic and connector information. Occurs mostly on a vehicle that is accelerating or decelerating abruptly. When the forward sensor detects daytime conditions, the rearward sensor is inactive and the mirror stays in a high reflectance mode.
Such parts and methods have not been tested by Ford, and may not meet Ford's requirements for safety, performance, strength, quality, durability and corrosion protection. Remove the wheel and tire. Deflate tires on cracked wheels prior to removal of wheels from the vehicle. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Failure to follow these instructions will result in deformation of the closing plate which will weaken the crossmember. The accelerometers measure the vibration at both ends of the driveshaft, while the phototachometer measures the rotation speed and position reference. Failure to follow this instruction may result in serious personal injury.
For additional information, refer to the procedures in this section. Back-probing is a risky testing method due to the uncertainty of the probe connection and the possibility of damaging terminals. To install, reverse the removal procedure. Remove the rear seat cushion. For example, some network communication codes are continuous only.
Never attempt to use a type-A, -B, -C extinguisher, or water, as these items are ineffective and may accelerate a magnesium fire. Remove the exterior mirror nut cover. Testing that reveals normal module-output function confirms the need to analyze the module inputs. To install, reverse the removal procedure. If the source has not been identified, continue with the road test.
If irritation persists, seek medical attention or advice. Control Switch in this section. A loud chuckle is usually described as a knock. If the source of the symptom has been identified as a result of this test, proceed to the appropriate section for further diagnosis and repair. A vibration present twice each revolution of the component would be a second order vibration.
Insert a flat-blade screwdriver between the lower inboard retaining tab and the exterior mirror glass backing plate. If the harshness concern persists after the above steps, it is possible that some components are damaged. For example, if the corresponding engine rpm of a vibration concern on a vehicle is 2,400 rpm, the resulting engine frequency is 40 Hz. Item Description 1 Combination pliers 2 Side cutter pliers 3 Internal snap-ring pliers 4 External snap-ring pliers 5 Hose clamping pliers 6 Locking pliers 7 Long or Needle-nosed pliers Drilling and Threading Tool Symbols The drilling or threading tool symbols are used to indicate which type and size drill, thread-cutting device, or file is required for the procedure. If equipped, remove the 2 scrivets and both side radiator air deflectors. Remove the exterior mirror nut.