One filament is a supplemental brake light and the other a supplemental tail lamp. Just buy this Harley Davidson Touring 2012 Service repair manual now and you will get you job done immediately because in just a minute youll have your manual downloaded. Loosen ground terminal nut 4. Install hone in a high speed electric drill. Lockwasher Extend and retract jiffy stand several times to verify proper 4.
Clutch Shell Assembly Assembly Figure 5-30. The table below lists the periodic maintenance requirements Also, throughout this manual, you will be instructed to use for Touring model motorcycles. Using non-approved tires can adversely or distort hub flanges. Allow the brake caliper to hang by the brake hose. Install cam support plate over guides.
Tug on fuel line fitting to verify that it is locked in position. Remove two flange nuts and backplate 1. Vertical: Turn both adjusters equally to adjust the light beam up and down. Position saddlebag on motorcycle aligning holes in grom- mets with those in front and rear mounting brackets. Purge and Disconnect Fuel Line To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Clean and install transmission drain plug.
Fork mounted fairing models: Install fairing cap. Remove two elbow connectors from neutral switch posts. Disassemble the lifter covers as follows: Separate upper 2 and lower push rod covers 8. Remove Spacer from Lower Bushing Installation Figure 2-89. Tap Push the un-notched ends of the rocker arm shafts into Figure 3-36.
They are specifically written for the do-it-yourselfer as well as the experienced mechanic. Remove O-ring from dowel pin 4 on base of cylinder deck. A-2 Mating Pin and Socket Housings. Short screw 6 Figure 6-32. Use of the wrong O-ring will have the same results.
Remove rocker arm support plate. Tighten to 18-22 ft-lbs 24. Connect speedometer 4 and tachometer 5 gauge connectors. Do not allow problems to develop. Antidotes for Battery Acid battery is extracted far enough to get a good grip, grasp battery and remove the rest of the way. Slide rubber boot off clutch cable adjuster. Replace cable fitting O-ring if damaged or deformed.
Replace ring if end gap exceeds specification. Slide shifter lever centering spring 3 hold the pawl on the cam pins. Harley-Davidson Service Manuals Please visit our brand new home page to see a complete list of all available Harley Davidson motorcycle service manuals. Tighten left side screws to 96-144 in-lbs 10. Packed with helpful information on how to operate and care for your 2012 Harley Davidson Touring motorcycle. Loosen ground terminal nut 4. To perform all repairs listed in this manual, a complete set of standard tools, as well as the special tools and fixtures shown and listed are necessary.
After downloading your 2012 Harley Davidson Touring service manual you can view it on your computer or print one or all of the pages needed. If the location of the valve seat is not correct, repeat steps 10 and 11. Remove center backrest from Tour-Pak lid. Failure to follow warnings and directions can result in death or serious injury. Insert spacers into new bushings until flush with outboard side of collar. However, if full engagement or full lever travel is not achieved, adjust the shifter rod.
Top stabilizer link bolts Rear frame bolts 40-50 ft-lbs 54. Loosen horn bracket bolt to front cylinder head. Verify that gauges are properly aligned and tighten screws to 10-20 in-lbs 1. Rear ring dowel Figure 3-95. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. If adjuster screw is adjusted with powertrain hot, clearance at push rod bearing could be insufficient with powertrain cold and clutch slippage could occur. If equipped, disconnect fender tip lamp connector.
. Apply a coat to the end of the handlebar. Bulb Replacement sm05135 When replacement is required, use only the specified sealed beam unit or bulb, available from a Harley-Davidson dealer. You can pay for your 2012 Harley Davidson Touring service manual with Paypal or Visa, MasterCard or Discover. Cam Compartment Service Only Remove induction module.