Dealer traced problem to fuel pump relay. Look at the base of the battery for bolts. Brought to dealer for replacement. Animals love its sweet taste, so even a spilling a small amount on your garage floor can end up in the dog's stomach pretty quickly. Thank you for your help, but I assume your have never changed a ect sensor on on this particular vehicle. Two days, more than a spark plug. If the housing is stuck, tap it lightly with a rubber head hammer.
Scrape off the old gasket from the cover, and install the new gasket in its place by spreading a thin layer of gasket adhesive where the gasket sits. Place an empty 2-gallon bucket under the very front end of the Jeep. Read on to learn how to replace your thermostat. Reconnect the heater core hose and the radiator hose, and clamp them down. Replaced thermostat, and cleared code.
The vehicle stalls while driving. Looks like with some mods to the housing a 44mm Stant Superstat could be fitted, since smaller than to O'ring the only difficulty I see would be clamping it in place. Step 8 On the six-cylinder, 5. If the temperature continues to climb past that point you may have air in the cooling system or a part of your cooling system may need to be replaced or upgraded. When you start your car, the thermostat blocks the coolant from going into your engine until the engine is hot enough, then it opens up and allows the coolant to go into the engine to keep it from overheating. The thermostat is a key component in the cooling. Keep a rag underneath it to avoid any small spills.
We have all seen cars pulled over to the side of the road, the hood raised, steam pouring out from under the hood. Is this what others are seeing? It should not be visible to you. Problem was attempted to fix once and persisted after vehicle was initially returned. Towed to dealer and picked up next day. Is there something else I'm not doing right? Install the cover on top of the gasket and tighten the two bolts. Vehicle towed to dealer for repair. Or there's more than one sensor? Some coolant will leak from the housing.
Car failed to start intermittently. You should probably consider changing the thermostat on your Jeep. Will find out more precisely when the new thermostat assembly gets here on back order. Remove the thermostat housing from the cylinder head. The serpentine belt might be in the way of the lower bolt.
Once this is done, pull up and the battery should come out. Jan 23, 2016 For jeep grand Cherokee fuel injectors replacing, i suggest you to go the help oink provided below:----- Its a complete step by step procedure to do so:----- Fuel Injector Replacing Jeep Grand Cherokee ------------- How to Replace a Fuel Injector ----------- How to Test and Replace Fuel Injectors on Acura Car Models? Always wear safety goggles when working on your Grand Cherokee. Nice timing on the article it caught my attention and helped me out alot! At first I thought it was the lower rad hose, but I then traced it to the upper rad hose coupling where it bolts to the water pump. Set the thermostat with the little burp valve as seen in the above picture facing upwards into the cylinder head. If any are detected, allow the engine to cool and tighten the hose clamps, bolts or replace the gasket and sealant or the rubber O-ring as necessary.
Step 2 Drain the cooling system. If you have a gasket, then you can skip this part. Truck died on the freeway. Mix the coolant with distilled water so that you have a combination of 50% coolant and 50% water. What I Have: 1994 Grand Cherokee Limited 2. If the belt is in the way, just loosen the tensioner and push the belt out of the way.
Step 11 Refill the coolant to the system and then start the engine and allow it to reach normal operating temperature. Promptly wipe up any spilled fluid as it is highly toxic. Step 4 After locating the thermostat housing, squeeze the tabs on the hose clamps and move them back several inches on the hose away from the housing. The vehicle has been in the shop for 21 days now. Bolt the thermostat housing back on.
The top one is much longer than the bottom one. Lastly press and release just the lock…. There is a recessed circle in the cylinder head for the thermostat to sit in. Turn the Jeep on to circulate the antifreeze. Had to pay for repair, submitting for refund on recall.