In this case, increase electrical load by operating devices such as the wiper motor and rear window defogger. When removing the exhaust camshaft be sure the subgear is not loaded; all the force must be eliminated. Install or connect the following: Alternator. Install the right cylinder head cover as follows: Fig. Apply a light coat of engine oil to bolt threads and under the bolt heads. Loosening the drive belt tension when equipped with an automatic drive belt tensioner.
Before servicing the vehicle, refer to the Precautions section. Position the intake camshaft on the head so that the alignment mark is at a 90 degree angle from vertical. Some versions of this method of mounting use an adjuster which is built into one of the components mounting braces. Install the cylinder head covers with the 12 bolts. Before servicing the vehicle, refer to the Precautions section. Do not damage the baffle plate when removing the head cover. Apply seal packing part No.
Align the timing marks of the left side camshaft pulley and the timing belt rear plate. Camshaft bearing cap bolt tightening sequence-3. While turning the belt tensioner counterclockwise, align with its holes, and then insert the 5mm bihexagon wrench into the holes to fix the belt tensioner. If the condition is not good, repair or replace the generator wire. It may just be a small fault.
It may just be a small fault and. Using the proper tool, slightly turn the right side timing pulley clockwise. Tons of pictures and diagrams at your fingertips!! Remove the valve lash adjuster shims and hydraulic lash adjusters. Apply seal packing part No. Inspect the tensioner assembly on the component; the tensioner adjusting bolt may use a locknut or screw to prevent it from loosening over time. All worn or damaged drive belts should be replaced immediately.
Cracks will usually start at the inner edge of the belt and run outward. So is Lexus still selling manuals on the older cars? Using an ohmmeter, measure the resistance between the terminals. Exhaust camshaft bearing cap bolt tightening sequence on the right cylinder head-3. Then set the belt to the idler pulley. Check the reading on the ammeter. Disconnect the engine wire from the cylinder head covers.
Retightening camshaft bearing cap bolts, Step 2-3. Breaking down is inevitability with all cars in time. Install the V-bank cover by engaging the 2 retaining clips and installing the 3 nuts. Before servicing the vehicle, refer to the precautions in the beginning of this section. Wait at least 90 seconds before performing any other work. Install the bank 1 cylinder head cover as follows: Page 48 Fig. Disconnect the negative battery cable.
Idler Pulley Without Adjusting Bolt 1. Install or connect the following: Valve lash adjusters and shims. Install the front suspension upper brace center. Tighten the oil check valve bolt on the cylinder head side to 44 ft. They are copywritten so I doubt if you will find them on forum websites where forum admins often prohibit them. Disconnect the negative battery cable.
Uniformly loosen and remove the exhaust camshaft bearing cap bolts in several passes and in the proper sequence. Disconnect the electrical connector from the sensor. Identify each lash adjuster and shim as it is removed so it can be reinstalled in the same position. Seal packing to bearing cap No. Exhaust camshaft installation position on the right cylinder head-3. Complete step-by-step instructions, diagram's, illustration's, wiring schematics, and specifications to completely repair your vehicle with ease! A new belt can be expected to stretch a bit after installation so, be prepared to readjust your new belt, if needed, within the first two hundred miles of use.
Wait at least 90 seconds before performing any other work. To remove the exhaust and intake camshafts from the right side cylinder head: Fig. Cylinder head valve covers M. Place the exhaust camshaft on the cylinder head. Install the bank 2 cylinder head cover as follows: A.
This manual very useful in the treatment and repair. Before servicing the vehicle, refer to the Precautions section. While releasing the belt tension by turning the belt tensioner counterclockwise, and remove the drive belt from the belt tensioner. Drive belt tension value chart. Now finish removing the belt from the other pulleys and remove it from the engine. Stationary Type Idler Pulley With Adjusting Bolt 1. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment.